Model Trimming

From Open Tech Dental Wiki 4.0
Revision as of 05:20, 21 September 2017 by Precident (talk | contribs) (Created page with "Rumeno * '''One View''': în timpul fazei Margini tăiate, aceasta arată doar un maxilar la un moment dat * '' Three Views '': în timpul celorlalți pași, toate informații...")
Jump to: navigation, search


Model Trimming

Instrumentul de tăiere a modelului face parte din modulele suplimentare ortodontice și de amprentă. Este nevoie de una sau două arcade aliniate achiziționate de la scaner și închideți meshurile modelelor cu o bază tăiată.

Instrumentul este lansat făcând clic pe butonul ActionOrtoBase.jpg din Main Toolbarcare apare când proiectul are cel puțin un mesh de model gata.

Interfață

Interfața instrumentului Model Trimming este diferită de restul software-ului. În partea dreaptă sus, există 4 tabele, câte unul pentru fiecare etapă a procesului. Restul ecranului este unul sau 3D:

Rumeno

  • One View: în timpul fazei Margini tăiate, aceasta arată doar un maxilar la un moment dat
  • Three Views : în timpul celorlalți pași, toate informațiile sunt afișate împreună pentru a permite utilizatorului să vadă totul din trei puncte de vedere diferite în același timp

Steps

The procedure develops in 4 steps:

  1. Move Jaws : adjusts the position of the jaws to respect some reference planes (occlusal plane and simmetric plane)
  2. Cut Margins : draws a margin line on the mesh to cut away all the information that will be replaced by the trimmed base
  3. Adjust Bases : changes the shape/position of the trimmed bases to adapt to the jaws
  4. Finalize : creates the finalized meshes, merging the cut jaws with the trimmed bases

Move Jaws

The positions of the jaw meshes, acquired from the scanner, may vary. This tool allows the user to adjust the position of the meshes with the aid of some commands.

For each movement there are 4 buttons (-10, -, +, +10), which apply a specific movement to the objects.

All the movements (rotations and translations) are defined according to an Axis. The axis can be seen in the 3D views, on the bottom-left angle.

There's an additional option, Show Bases, that allows the user to see a preview of where the trimmed bases will be, in order to aid the positioning process.

Dental 2 5 ortoBasePosition.jpg

Cut Margins

The jaw meshes acquired from the scanner often have residual unnecessary parts of information. This parts have to be removed before merging the data with the new trimmed base.

Fort his purpose, an interactive tool that can draw a line on the mesh surface is provided:

  1. The first left mouse click on the mesh surface creates a point and starts the margin definition
  2. Any additional left mouse click adds a point to the margin and connects it to the previous one
  3. A left mouse click on the first point closes the margin
  4. After the margin is closed, the user can:
    • drag one point with the left mouse button to move it to a different position
    • click between two points, to add a new point in the middle
    • press ESC to delete the margin and start again

When the margin is defined, a click on the Cut button will remove all the parts of the mesh below the margin.

Dental 2 5 ortoBaseCut.jpg

Adjust Bases

The user can change 4 different parameters of the bases. When a parameter is changed, the 3D view updates in approximately 2 seconds.

  • Width : the maximum width of the base
  • Length : the maximum length of the base
  • Height : the base height
  • Distance : distance between the two bases, which are symmetric to the occlusal plane

After the cut, the jaw meshes have to be completely fitted in the bases. If the bases are too small a warning message will appear below the parameters.

Dental 2 5 ortoBaseAdjust.jpg

Finalize

This last page shows only the Finalize button. When clicked, the software takes all the data and computes the new, closed, mesh. This process can take up to 2 minutes.

If the result is not satisfactory for the user, it is possible to return to one of the previous steps, change parameters and positions and then return to the Finalize step and compute the meshes again.

Otherwise, if the finalized mesh is satisfactory, click Ok to confirm the base trimming and save the new meshes.

Dental 2 5 ortoBaseFinalize.jpg

Dental 2 5 wiz prev.png Homebutton.png Dental 2 5 wiz next.png