Acquisition

Erfassung

Die Datenerfassung mit der Erstellung einer 3D-Version des Gegenstands ist die Hauptfunktion der OpticalRevEng Dental Software.

Für weitere Informationen über den geleiteten Prozess siehe Seite "Wizard".

Bei einem Strukturprojekt gibt es drei verschiedene Wege, um Informationen ohne den geleiteten Prozess zu erfassen.

Einfach

Das ist der einfachste und meistbenutzte Weg zur Datenerfassung:

1. Gegenstand in den geeigneten Modellhalter eingeben
2. Das zu scannende Element im Projektbaum auswählen
3. Auf das Erfassungicon in der Hauptwerkzeugleiste klicken

Das Gerät scannt den Gegenstand mit der entsprechenden Scanmethode und der Projektbaum-Status wird upgedatet.

Erweiterte Optionen

To use an acquisition strategy different from the default, hold the button when clicking on the Acquisition icon.

An addittional dialog will allow to choose a different strategy and a color for the object that needs to be acquired

Dynamic Articulation

If the Dynamic Articulation Module is enabled and in use, the software will remind the user to scan the jaw on top of the adequate base.

The base to be used depends on the type of articulator chosen in the project definition.

If the base type doesn't match the type of articulator, the positioning in Exocad Virtual Articulator won't be correct.

Multi-Die

To acquire multiple dies in a single scan, even from both jaws at the same time, using the multi-die support:

1. Select from the Project Tree all the dies to be scanned
2. Click the Multi-Die Acquisition button that will appear on the Main Toolbar. At least 2 dies have to be selected in the Project Tree
3. Put the dies in each space of the support, as shown by the software in the top right window, and put the Multi-Die support inside the scanner
4. Click the Start Acquisition button

The scanner will acquire the data, identifying every single die and updating the status of the Project Tree

Single

To acquire a single 3D image, and not a 360° object reconstruction (for testing or to acquire a big articulation in a small scanner):

1. Put the object inside the scanner, in the best possible way
2. Use the Single Acquisition tool

The software will carry out a single acquisition without moving the motors system

Integration

After an object has been acquired in the scanner, there could be the need to add further information to the starting scan. For example, part of the object may be missing due to shadows or because the acquisition strategy has not covered a specific point of view.

In order to integrate additional information, use the Integrate Acquisition button on the Main Toolbar. This will launch the Integration Mode, providing 3 different integration tools. It is possible to switch from one tool to another. Confirm the modification with the Apply button or discard it with the Cancel button.

It is possible to add an unlimited number of acquisitions but adding to much data could slow down the project and increase the project disk size.

Single

The single integration mode allows to add information from a specific point of view. To add information:

1. Rotate the 3D view so that the screen will show exactly the part of the object to be integrated
2. Click on the Start Integration icon

If the last added acquisition is not good, useless or problematic, it is possible to remove it with the Undo button.

If the object is not in the original scanning position, the software can not correctly integrate the information. It is possible to try to fix this problem using the Calc Integration Position button.

Custom

The Custom mode, instead of scanning one position at a time, allows to create a costumized sequence of positions and then the scanner will carry out all the acquisitions together.

To add a position:

1. Rotate the 3D view so that the screen will show exactly the part to be integrated
2. Click the Add Position button

To remove a position:

1. Select the position from the list
2. Click the Remove Position button

To start the scan, click the Start Integration button

Full

The full integration is the easiest mode: it allows to select as many positions as needed and in which degree the plate must tilt to complete the image.
Then, by clicking the Start Integration button, the scanner will tilt the model and carry out a 360° acquisition using the selected number of positions.

Change Strategy

When the Project Tree is created, the software will select a specific strategy for every element, trying to maximize the scan quality and saving space. To change the strategy of an element of the project:

1. Right click on the element in the project tree
2. Select Change Strategy
3. Select the new strategy from the dropdown menu

Another scan of the object will be carried out using the new strategy instead of the old one.