Difference between revisions of "Man Acquisition/ja"

From Open Tech Dental Wiki 4.0
Jump to: navigation, search
(Created page with "= 取得 =")
(Created page with "スキャナーからデータを取得し、オブジェクトの3D表示を作成することは、スキャニングソフトウェアの主要な機能となります。")
Line 3: Line 3:
 
= 取得 =
 
= 取得 =
  
Acquiring data from the scanner and creating a virtual 3D representation of an object is the primary function of the OpticalRevEng Dental software.
+
スキャナーからデータを取得し、オブジェクトの3D表示を作成することは、スキャニングソフトウェアの主要な機能となります。
  
 
For additional information about the Step-By-Step Wizard, check the [[Wiz_Acquisition|Wizard Acquisition]] page.
 
For additional information about the Step-By-Step Wizard, check the [[Wiz_Acquisition|Wizard Acquisition]] page.

Revision as of 03:33, 29 December 2015


取得

スキャナーからデータを取得し、オブジェクトの3D表示を作成することは、スキャニングソフトウェアの主要な機能となります。

For additional information about the Step-By-Step Wizard, check the Wizard Acquisition page.

In a Structured Project outside the wizard, there are 3 procedures to acquire data from the scanner.

Simple

This is the easiest way to acquire data, and the most used:

  1. Put the object inside the scanner on the appropriate model holder
  2. In the Project Tree, select the object to scan
  3. Click the Acquisition icon on the Main Toolbar

The scanner will then acquire the object using the strategy of the selected element and the status of the Project Tree will be updated.

Denta 2 5 simpleAcquisition.gif

Advanced Parameters

To use an acquisition strategy different from the default, hold the Key shift.png button when clicking on the Acquisition icon.

Adv-acqui.JPG

An addittional dialog will allow to choose a different strategy and a color for the object that needs to be acquired

Dynamic Articulation

If the Dynamic Articulation Module is enabled and in use, the software will remind the user to scan the jaw on top of the adequate base.

Msg art.PNG

The base to be used depends on the type of articulator chosen in the project definition.

If the base type doesn't match the type of articulator, the positioning in Exocad Virtual Articulator won't be correct.

Multi-Die

To acquire multiple dies in a single scan, using the multi-die support:

  1. Select from the Project Tree all the dies to be scanned
  2. Click the Multi-Die Acquisition button that will appear on the Main Toolbar. At least 2 dies have to be selected in the Project Tree
  3. Put the dies in each space of the support, as shown by the software in the top right window, and put the Multi-Die support inside the scanner
  4. Click the Start Acquisition button

The scanner will acquire the data, identifying every single die and updating the status of the Project Tree

Dental 2 5 multiDieAcquisition.gif

Single

To acquire a single 3D image, and not a 360° object reconstruction (for testing or to acquire a big articulation in a small scanner):

  1. Put the object inside the scanner, in the best possible way
  2. Use the Single Acquisition tool

The software will carry out a single acquisition without moving the motors system

Integration

After an object has been acquired in the scanner, there could be the need to add further information to the starting scan. For example, part of the object may be missing due to shadows or because the acquisition strategy has not covered a specific point of view.

In order to integrate additional information, use the Integrate Acquisition button on the Main Toolbar. This will launch the Integration Mode, providing 3 different integration tools. It is possible to switch from one tool to another. Confirm the modification with the Apply Dental 2 5 confirmButton.png button or discard it with the Cancel Dental 2 5 cancelButton.png button.

It is possible to add an unlimited number of acquisitions but adding to much data could slow down the project and increase the project disk size.

Single

The single integration mode allows to add information from a specific point of view. To add information:

  1. Rotate the 3D view so that the screen will show exactly the part of the object to be integrated
  2. Click on the Start Integration Dental 2 5 startIntegrationButton.png icon

If the last added acquisition is not good, useless or problematic, it is possible to remove it with the Undo Dental 2 5 undoLastIntegrationBtn.png button.

If the object is not in the original scanning position, the software can not correctly integrate the information. It is possible to try to fix this problem using the Calc Integration Position button.

Dental 2 5 integrateSingle.jpg

Custom

The Custom mode, instead of scanning one position at a time, allows to create a costumized sequence of positions and then the scanner will carry out all the acquisitions together.

To add a position:

  1. Rotate the 3D view so that the screen will show exactly the part to be integrated
  2. Click the Add Position Dental 2 5 confirmButton.png button

To remove a position:

  1. Select the position from the list
  2. Click the Remove Position Dental 2 5 cancelButton.png button

To start the scan, click the Start Integration Dental 2 5 startIntegrationButton.png button

Dental 2 5 integrateMulti.jpg

Full

The full integration is the easiest mode: it allows to select as many positions as needed and in which degree the plate must tilt to complete the image.
Then, by clicking the Start Integration Dental 2 5 startIntegrationButton.png button, the scanner will tilt the model and carry out a 360° acquisition using the selected number of positions.

Dental 2 5 integrateFull.jpg

Change Strategy

When the Project Tree is created, the software will select a specific strategy for every element, trying to maximize the scan quality and saving space. To change the strategy of an element of the project:

  1. Right click on the element in the project tree
  2. Select Change Strategy
  3. Select the new strategy from the dropdown menu

Another scan of the object will be carried out using the new strategy instead of the old one.

Dental 2 5 wiz prev.png Homebutton.png Dental 2 5 wiz next.png