Man ProjectCreation/it

Progetto

Quando si lancia il software direttamente, se il progetto non fosse stato definito in un database esterno come il DentalDB di Exocad, è necessario definire il progetto di Scansione.

Il software ha una finestra di Definizione del Progetto in cui vengono immesse tutte le informazioni necessarie a proposito degli elementi da scansionare. Il tipo di informazione immessa definisce poi la Procedura Guidata.

Durante la definizione si possono selezionare uno dei tipi di progetto disponibili cliccando sulle relative icone riportate nella barra sulla sinistra della finestra.

Tutti i tipi di progetto richiedono alcune Informazioni Generali:

• Il nome del Paziente (Obbligatorio)
• Il numero del Dottore (Opzionale)
• Un nome progetto specifico per il salvataggio sul disco; qualora non venisse stabilito, il nome progetto si genererà automaticamente sulla base del ID del paziente
• Il nome del Tecnico (Opzionale)
• Note (Opzionali)

Per confermare la definizione del progetto, fare click sull'icona verde nella parte inferiore della finestra. Il software creerà un Progetto Strutturato e avvierà la Procedura Guidata.

Progetto Protesi

Cliccando sull'icona si abilita la definizione di un Progetto di Protesi.

The prosthesis section is the most complex because of the amount of elements that can be set and which require a tooth by tooth definition.

Other than the General Information section, this project shows 2 additional sections

Project Definition

In the main part of the window, an odontogram is available that allows to define the elements that have to be scanned.

By holding when clicking on a tooth, the last selected item will be copied to the selected tooth.

By holding when clicking on a tooth, the last set parameters will be copied to all the teeth between the last tooth and the selected one.

Tooth Information

The section in the bottom right corner allows to select the Tooth Type and some Other Options for each selected element. The Tooth Types are:

• None : this tooth is not part of the project, it will not be acquired or can be ignored
• Healthy : this tooth is part of the main stone model, it can be acquired with the rest of the model
• Stump : this tooth is a removable die that has to be acquired alone or on the Multi-Die support
• Pontic : missing tooth in between two stumps, it will be the intermediate element of a bridge
• Implant : there is an implant in this position, therefore a Scan Body will be acquired
• Bite : this tooth is part of an occlusal bite

Every tooth type has a specific color in the project definition scheme.

The Other Options are:

• Gingiva : this element is mounted on an artificial gingiva that has to be acquired separately from the stone model
• Pre-Op: the anatomy of this element is part of an additional model that will be acquired separately and then aligned to the reference stone model
• Waxup : over this tooth position, it's possible to scan a Pre-Modelled Waxup that will be aligned to the rest of the stone model

Additional Parameters

In the general information section, there are some additional parameters:

• Face Scan : if this option is enabled and available, a Real Time Face Scan will be added to the project data
• Unsectioned Model : enable this option if the model is not sectioned and the stumps can't be acquired separately
• Impression : enable this option if, instead of a stone model, an impression needs to be scanned

If the Dynamic Articulation Module is enabled, another option is displayed.

In the Articulator section select:

• Matching models to scan the occlusion if there is no need to use the automatic positioning in Exocad's Virtual Articulator
• Articulator A to scan the Artex Articulator and to use the same in Exocad's Virtual Articulator
• Articulator S to scan the Sam Articulator and to use the same in Exocad's Virtual Articulator
• Articulator P to scan the Kavo Articulator and to use the same in Exocad's Virtual Articulator

Here below an example of a defined prosthesis project for a 3-elements bridge with a stone antagonist:

Multi-Die Project

Use the Multi-Die Project to scan different dies from different patients in one single project:

To set the case, click on each multi-die position and define the name of each patient in the Patient field.

Orthodontic/Scheletric/Impression Project

The Orthodontic, Scheletric and Impression Projects are straightforward and similar to one another.

These projects require the user to select the whole jaws instead of individual teeth.

When the project definition is confirmed, the software will prepare the Project Tree to acquire the data from the scanner.

Project Editing

If the project definition needs to be changed while already in use, it is possible to select the Edit Project tool in the File Menu or in the Project Toolbar (See Support Toolbars And Menus).

This tool will open again the Project Manager with the current project definition. It is possible to change the project definition and the parameters of every tooth.

When the editing is confirmed, the software will adapt the Project Tree. Editing an already scanned, or partially scanned, project can cause data loss.