Wizard Acquisition

From Open Tech Dental Wiki 4.0
Revision as of 12:24, 24 September 2017 by Precident (talk | contribs) (Created page with "Este foarte ușor să urmăriți wizard:")
Jump to: navigation, search


Achiziționarea Wizard =

În timpul Wizard pas cu pas, este posibil să: achiziționați obiecte unice sau mai multe obiecte într-o singură scanare, să re-achiziționați un obiect achiziționat anterior și să integrați toate aceste achiziții.

Obiect unic

De fiecare dată când un element trebuie achizitionat, se va afișa un anumit ecran expert:

  • Numele obiectului care urmează să fie achiziționat
  • O scurtă descriere a ceea ce ar trebui scanat
  • Un selector pentru Object Color
  • Un buton Scan pentru a începe achiziția
  • Un buton Integrate pentru a începe integrarea unui obiect dobândit anterior
  • Already Aligned verifică , arată dacă acest obiect este deja aliniat la restul proiectului

Este foarte ușor să urmăriți wizard:

  1. Read the object description
  2. Put the right object inside the scanner
  3. Click Scan
  4. If the acquisition is not satisfactory, click again the Scan button to start a new acquisition, or the Integrate button to add data

Dental 3 5 wizAcquire.PNG

Open Live

It is possible to open the live view of the cameras, by clickin on the OpenLive.png to see the progress of the scanning in the monitor of the computer.

Advanced Parameters

During the wizard the acquisition strategy is selcted automatically depending on the kind of element to acquire.

There are some specific cases, however, in which it might be necessary to change the scanning strategy to a non default one. For instance, if the user needs to scan abutments instead of stumps, it would be best to select the specific abutment strategy. Same goes if the user needs to design a veneer: it is not a default strategy for stumps but it can be selected during acquisition.

To change strategy, click on the StartServiceButton.jpg button and select it from the drop down menu.

Copy From Reference

Sometimes, one element data has already been scanned during another acquisition.

For example, the acquisition of the healthy and pontics parts of the jaw is similar to the reference acquisition of the entire jaw, except for the stumps, which will be acquired in a separate step.

In these cases, the software will show the existing image and automatically remove the parts already scanned in detail. It is always anyways possible to copy the whole image again by clicking Copy From Reference or to start a new acquisition if the cut copy is not satisfying.

Dental 3 5 wizHealthyAcquire.PNG

Multi Acquisition

When acquiring multiple dies or multiple implants, it's better not to carry out a single acquisition for every element.
It is possible to acquire many objects at once.
Just make sure that the objects are completely visible in all their parts and that they are at an adequate distance either on the model holder or on the Multi-Die support.
In these cases, the software will show a Multi-Acquisition Setup step where it is possible to select the objects to be scanned at the same time.

This step will show a list of all the objects that have to be scanned together with the already acquired items. Flag the boxes of the objects that have to be scanned together and, when scanning stumps,the flag Use Multi-Die support option on the bottom of the dialog will be checked by default to allow the use of the Multi-Die holder.

Dental 2 5 wizMultiStump.jpg

With Multi-Die

If the Multi-Die option is selected, the software will set up a specific acquisition for the dies; an image will guide the user in positioning the dies in the Multi-Die holder.
After the acquisition, the software will automatically recognize each single die and return to the Multi-Acquisition Step to allow the acquisition of additional objects.

Dental 2 5 wizMultiDieAcquisition.jpg

Without Multi-Die

If the Multi-Die gets deselected, the software will acquire the objects and, in the following step, require the user to manually identify each object.
A specific Wizard Step will ask which object has to be identified. The user has to:

  1. Read from the Wizard Page which object has to be selected
  2. Select the specific object, using a Selection Tool
  3. Click the button Segment
  4. Click the button Next

Dental 2 5 wizStumpSegment.gif

When the objects are all identified, the software returns to the Multi-Acquisition step. If all the objects have already been aquired, click Next to continue with the Step-By-Step Wizard

Dental 2 5 wizMultiStump-after.jpg

Integration

By clicking the Integrate button after an acquisition, the Integration mode will be launched.

Dental 2 5 wiz prev.png Homebutton.png Dental 2 5 wiz next.png