Dy Mod - Revision history

L.Pizzoli at 09:37, 16 December 2016

2016-12-16T09:37:55Z

Admin at 11:09, 27 November 2015

2015-11-27T11:09:25Z

L.Pizzoli: Marked this version for translation

2015-10-15T16:38:46Z

Marked this version for translation

E.pasotti: Created page with "{{Language bar}} {{DISPLAYTITLE:Dynamic Articulation Module|noerror}} The '''Dynamic Articulation Module''' allows the user to transfer the mastication position r..."

2015-10-13T10:10:17Z

Created page with "{{Language bar}} {{DISPLAYTITLE:Dynamic Articulation Module|noerror}} <translate> The '''Dynamic Articulation Module''' allows the user to transfer the mastication position r..."

New page

{{Language bar}}
{{DISPLAYTITLE:Dynamic Articulation Module|noerror}}
<translate>

The '''Dynamic Articulation Module''' allows the user to transfer the mastication position realized in the laboratory with a real articulator into its Exocad virtual equivalent.

When the '''Dynamic Articultion Module''' gets enabled, the user is provided with a set of 4 ''Mounting Plates'' and a ''Recalibration Object''. See [[Accessories|Accessories- Dynamic Articulation Module]]

Before using the Module for the first time it is necessary to calibrate the axis of the scanner to work accordingly to the occlusion simulation.

Calibrate the axis with the specific [[Accessories|Axis Calibration Object]]. From that moment on, any recalibration needs to be performed with the same object. Otherwise, axis recalibration will fail.

# Put the calibration object inside the scanner
# Click '''Recalibrate Axis'''
# Click '''Ok''' when prompted

The calibration procedure is automatic. Once it is finished, the software will show one of the following messages:

*'Axis Recalibration Successfull' : the calibration has been completed
*'Axis Recalibration Failed' : calibration has to be repeated

The following step is to set the correct Articulator Type during the [[Man_ProjectCreation|Project Creation]]. <br/>
In the ''Articulator'' section select:
* Matching models to scan the occlusion if there is no need to use the automatic positioning in Exocad's Virtual Articulator
* Articulator A to scan the Artex Articulator and to use the same in Exocad's Virtual Articulator
* Articulator S to scan the Sam Articulator and to use the same in Exocad's Virtual Articulator
* Articulator P to scan the Kavo Articulator and to use the same in Exocad's Virtual Articulator

Proceed scanning the physical Articulator, accordingly to the previously made choice.

Remember then to scan the jaws on top of the appropriate mounting plates, as the software will remind.

[[File:Msg art.PNG]]

If the base type doesn't match the type of articulator, the positioning in Exocad Virtual Articulator won't be correct.

</translate>
{{Navigation|Wiz_Export|Dental_Options}}

@@ Line 34: / Line 34: @@
 * Articulator S to scan the Sam Articulator and to use the same in Exocad's Virtual Articulator
 * Articulator P to scan the Kavo Articulator and to use the same in Exocad's Virtual Articulator
 <!--T:9-->

@@ Line 44: / Line 44: @@
 [[File:Msg art.PNG]]
- <!--T:12-->
-If the base type doesn't match the type of articulator, the positioning in Exocad Virtual Articulator won't be correct.
+<!--T:12-->
 </translate>
 {{Navigation|Wiz_Export|Dental_Options}}

@@ Line 3: / Line 3: @@
 <translate>
 The '''Dynamic Articulation Module''' allows the user to transfer the mastication position realized in the laboratory with a real articulator into its Exocad virtual equivalent.
 When the '''Dynamic Articultion Module''' gets enabled, the user is provided with a set of 4 ''Mounting Plates'' and a ''Recalibration Object''. See [[Accessories|Accessories- Dynamic Articulation Module]]
 Before using the Module for the first time it is necessary to calibrate the axis of the scanner to work accordingly to the occlusion simulation.
 Calibrate the axis with the specific [[Accessories|Axis Calibration Object]]. From that moment on, any recalibration needs to be performed with the same object. Otherwise, axis recalibration will fail.
 # Put the calibration object inside the scanner
 # Click '''Recalibrate Axis'''
 # Click '''Ok''' when prompted
 The calibration procedure is automatic. Once it is finished, the software will show one of the following messages:
 *'Axis Recalibration Successfull' : the calibration has been completed
 *'Axis Recalibration Failed' : calibration has to be repeated
 The following step is to set the correct Articulator Type during the [[Man_ProjectCreation|Project Creation]]. <br/>
 In the ''Articulator'' section select:
@@ Line 27: / Line 35: @@
 * Articulator P to scan the Kavo Articulator and to use the same in Exocad's Virtual Articulator
 Proceed scanning the physical Articulator, accordingly to the previously made choice.
 Remember then to scan the jaws on top of the appropriate mounting plates, as the software will remind.
 [[File:Msg art.PNG]]
-  If the base type doesn't match the type of articulator, the positioning in Exocad Virtual Articulator won't be correct.
+  <!--T:12-->
 </translate>
 {{Navigation|Wiz_Export|Dental_Options}}